M O D I F I C A T I O N S : TUNING, Engine
When going for real power gains, adding an airfilter and buying a sports exhaust system isn''t a solution anymore. Don't forget, they are providing the best power for money ratio, but the power enhacement is limited and at a certain stage too low. Starting with them isn't a waste of money, as they are becoming more restrictive while tuning the engine on a further level.
What can be done:
- Changing the inlet (manifold) and/or
throttle body (here),
optimising the amount of air and fuel.
Standard VVC Inlet manifold,
or more precise: the plenum chamber
- Fitting other camshafts:
a new set of cams will change the time that a valve opens and closes and the
lift of the cam.
- Porting and polishing
heads allows the engine to breath better and deeper.
- Fitting larger, differently shaped valves:
Improving the induction system, e.g. fitting throttle bodies, can greatly increase
the airflow into the engine, but beyond a certain level of engine tuning this
is no longer enough. As an engine is more highly tuned, and particularly as
the CR is raised, it becomes increasingly important to improve gas flow through
the head. This doesn't just mean work on the inlet and exhaust ports but also
means changing the valves.
- Fitting a turbo, supercharger
and all that kind of expensive stuff
- Installing a Power boost valve, aftermarket
ECUs and chips (ICON Race for example).
These devices will change the values comming from the sensors, providing the
ECU all the info for injection and ignition. Don't expect too much from these
on a non-Turbo-ed car. Other kind of chips are needed when some serious engine
tuning is involved as the standard ECU can not be reprogrammed. (more about
chips and magic boxes here)
- A new set of Ignition Leads (more info
here) and plugs.
- Changing the K-series engine for another
one is rather new: MG-Rover's KV6, Honda Civic Type-R, ...
I've also created a page,
that will show you some small things on how to make your engine
more secure.
The following page shows something more
about the timing of a K-series engine.
First I must add that I
don't know very much about technics --still kind of learning-- so maybe it's
wise to have a look at all kind of providers and what they are offering . .
. Going through the page you will find parts, kits, etc. from:
Mike Satur
Moto-Build
Southern
Carburettors
Powertrain
Projects
Turbo-Technics
QED Motorsport
BBR-GTi
MG XPower
Spen Vale
Garage
When MG Rover launched the
TF, they were and still are providing an 1.8 MPi with 135bhp, while the F MkI
and MkII had only 120bhp. This power gain is achieved by using a new airfilter
box, the trophy throttle body and a redesign of the exhaust system. In the beginning
we were not sure about the cams, but we must agree that the cams have been changed
slightly.
1.8 MPi
- Stage 1
Results in similar bhp figures to the VVC, more bottom end gain rather than
the top end gain
The standard 1.8i head is basically the same as the one fitted to the 1.4 K-series
engine. This results in restricted flow for the 1.8 engine. So tuning the engine
head involves gas flowing and porting with some work to the inlet valve profiles.
The standard valves and springs, (27.5mm inlet, 24mm exhaust) are retained.
This is a good mod for road use and frees the breathing up considerably. With
a suitable filter system BHP goes up to around 126 at the wheels while standard
is about 105BHP (tested by MG World). Similar gains in the torque are also achieved,
altogether a good budget option.
Supply only £450.00 (ex. VAT) Fitted with new gaskets oil etc. £850.00
(ex. VAT)
1.8 MPi
- Stage 1 Plus
An increased nhp figure
throughout the power band and with top end gains. In addition to the above (Stage
1) Mike Satur can fit a high lift inlet cam (10.87mm compared to the standard
8.8mm) with an adjustable cam gear, this allows the timing to be set accurately.
The high lift cam will give additional top end power and torque. New valve springs
are fitted to prevent coil binding. This addition costs an extra. Supply £310.00
(ex. VAT) Fitted to stage 1 head £310.00 (ex. VAT)
1.8 MPi
- Stage 2
This head is also extensively gas flowed and utilises larger valves (29.5mm
inlet, 26mm exhaust), a higher lift inlet cam and adjustable timing gears. With
filter and exhaust mods we have achieved 137BHP at the wheels on a 1.8i.
Supply only £750.00 (ex. VAT) and £1150.00 when fitted (ex.
VAT)
To optimise the power gains, Mike Satur recommends a higher lift inlet cam, adjustable vernier and new valve springs (£310.00 ex. VAT) A high lift exhaust cam and vernier can be fitted with some gain in BHP, but some lumpiness may occur (£235.00 ex. VAT)
1.8 MPi
- Stage 2 Plus
As Mike states: "... for those who love to work the engine"
This conversion gives optimum gains with new cams This involves fitting new
valves and valve seats to the same size as the VVC (31.5mm inlet, 27.5mm exhaust)
with reshaped ports and valve throats to give greater airflow, which results
in more power and torque.
Supply £950.00 (ex. VAT), Fitted £1350.00 (ex. VAT)
To optimise the power gains Mike Satur recommends a higher lift inlet cam, adjustable vernier and new valve springs (£310.00 ex. VAT). A high lift exhaust cam and vernier is recommended with more gain in BHP, some lumpiness may occur (£235.00 ex. VAT).
1.8 MPi
- Stage 3
Tthis modification is for the serious enthusiast requiring that few extra BHP.
Stage 2 plus the addition of bigger valves than the VVC (32.5mm inlet, 28.3mm
exhaust) and produces more power due to the better design of the valves and
greater air flow.
Supply £970.00 (ex. VAT), Fitted £1370.00 (ex. VAY)
To optimise the power gains Mike Satur recommends a higher lift inlet cam, adjustable vernier and new valve springs (£310.00 ex. VAT). A high lift exhaust cam and vernier is recommended with more gain in BHP, some lumpiness may occur (£235.00 ex. VAT)
1.8i performance
camshafts
"We have achieved excellent results with Piper camshafts, using profiles
that develop power throughout the rev range without having to 'pocket' the pistons
or change to solid lifters. Our 'fast road' profile is recommended for everyday
use." (Special FX, Mike Satur brochure)
VVC tuning
options
"The VVC is often ignored by tuners as being over complicated - not so
at Mike Satur! We have taken the standard VVC head and redeveloped the ports
to produce more power. Under development is a modified VVC camshaft to give
even more power." (Special FX, Mike Satur brochure)
New from
Mike Satur, the Clubman Kits
MGF 1.8i Clubman Kit (also fits the ZR and ZS cars)
"Consists of a reworked head with larger inlet valves and seats (31.5 mm
inlet up from the std 27.5mm dia) reprofiled throats ,ports, valves and combustion
chambers. The standard cams are retained but power gains up to 150BHP
can be achieved using our recommended manifold, sports exhaust , sports ca t.
and induction kit.Throttle response and torque are a considerable improvement
over the standard engine.The head is exchange or customers own unit and the
price is £675.00 plus vat A fitting service is available and this
costs £450.00 plus vat." (Mike Satur website)
MGF VVC
Clubman kit (Also fits ZR 160 cars)
"Consists of reworking valves, seats , throats and port profiles and revised
VVC cam timing, when coupled with our recommended air induction kit and exhaust
mods can produce around 175BHP with associated increase in torque and
throttle response. We recommend that we fit this kit due to the modifications
we make to the VVC mechanisms .Fitted price £895.00 plus vat"
(Mike Satur website)
Some Performance parts
Lightweight
Flywheel
"4.22 Kilos including ring gear, improve throttle and accelerator response,
ideal for tuned engines (£166.50 + VAT and delivery)." (source:
Mike Satur's website)
Uprated
Fuel Pump kit
"Standard AC Fuel pump flows approx 2 litres per minute at 3 BAR pressure.
For performance tuned vehicles under constant load this performance will drop
off and could cause fuelling problems. Our new high performance pump at 3bar
flows 4 litres per minute and will continue. (£110 + VAT and delivery)"
(source: Mike Satur's website)
1.8i MGF
Stage I
"Pipercross airfilter replacement assembly and performance silencer assembly.
This combination will yield 9BHP, removal of the catalyst yields a further 2BHP.
Total power now 128-137 BHP."
1.8i
MGF Stage II
"As Stage I, but with the inclusion of a remapped engine management ECU.
This combined with Stage I will provide an additional 16-17BHP. Total power
now 135-137 BHP."
1.8i
MGF Stage III
"As Stages I and II, but now with the addition of a pair of hydraulic type
camshafts. A different program is in the ECU, but if upgrading from Stage II
the ECU will be exchanged at no extra charge. Total power now 148-150 BHP."
1.8i MGF
Stage IV
"As Stages I, II, III, now with the addition of twin weber 45 DCOE carburettors,
filters linkages, pressure regulator and manifold. Total power now 175-180
BHP."
1.8 VVC
MGF Stage I
"Air filter replacement and performance rear silencer provides an extra
10-11BHP Total power now 155-157 BHP."
1.8 VVC
MGF Stage II
"As Stage I, but with the incusion of a reprogrammed ignition management
system a maximum of extra 20BHP is available (normally only if catalyst is removed).
Total power now 160-164 BHP."
1.8 VVC
MGF Stage III
"Currently under further development, but just under 200BHP is available
with our fully programmed fuel and ignition 4 throttle body management system.
Total power around 200 BHP."
All descriptions of
the Moto-build upgrade paths are grabbed from their website.
S o u t h e r n C a r b u r e t t o r s
"If you have already
bought a 1.8i MGF, but you're missing the extra power that a VVC could offer
you.... well read this. Southern Carburettors (SC) do many more things these
days than sell carburettors. Aside from the classic car restoration side of
the business, selling bolt-on tuning kits is the mainstay. For the MG's 'K'series
engine, the accent is on a simple bolt-on induction and exhaust kit to allow
the engine to breathe better and hence gain power and torque. And to make it
all work on best effect, a reprogrammed ECU replaces
the standard unit to enable adjustments of the fuelling and ignition mapping.
Central to the conversion is a multiple throttle body
assembly developed by SC for this application. This replaces the single throttle
butterfly fitted as standard with one butterfly for each intake tract. Its purpose
is to provide a far more accurately metered air supply for each individual cylinder
and, with a 45mm choke on each, it also allows a better flow rate. It's designed
to accept the standard fuel rail assembly and there's a carbon-fibre airbox
that matches up with the standard air filter. This conversion costs £1936
and the beauty of it is that the whole lot is a bolt-on kit that can be fitted
by the owner or by any local garage. Complementing the throttle body kit is
a performance exhaust to further enhance performance. The standard 1.8i engine
is pretty good, delivering 120bhp at around 5250rpm and with a reasonably flat
torque curve. With the SC conversion the engine delivers more power and torque
all the way through the range from 2000rpm upwards but, crucially, the power
range is extended beyond that of the standard engine. Where the stock engine's
power tails off beyond its peak at 5250rpm, the SC's better breathing allows
it to deliver strong power and torque until well beyond 6000rpm. More specifically,
it adds 20bhp, to provide a meaty 140bhp at 6000rpm, with at least 10
per cent more power than throughout the useable part of the rev range. In all
the through-the-gears tests the SC engine is quicker than the VVC." (Raby,
P., MG World Oct./Nov. 1998)
P o w e r - T r a i n - P r o j e c t s
Power-Train-Projects are offering their products on a very nice developed website. To have all the engine tuning posibilities listed on this page, I am copying data from their website to mine.
PTP are offering several upgrades for the F, some are engine related. Those upgrade paths can be divided in whole engines, performance parts and kits, containing some of the performance parts.
140
Performance 'K' Series Engine Assembly - £3995 (ex VAT)
Power 140ps
at 6500rpm
Torque 133lb/ft at 5000rpm
Power and Torque figures achieved with Janspeed performance exhaust, sports
catalyst and ITG performance induction system. Deviation form these parameters
may result in a different performance level.
The 140 performance package can be supplied in a Cylinder head kit form (see
Performance Kits (a bit further on this page (Erik))) or as a fully built, hot
tested engine configuration. The engine is SVA emissions compliant when used
with standard or PTP sports catalist converter. The engine delivers increased
power and torque with improved driveability and throttle response. It however
maintains the standard Rover Engine management system and control strategies
to maintain all service and diagnostic functionality.
The core of the package is a finely tuned cylinder head focusing not on metal
removal for maximim air flow but port chamber modifications to bestflow optimum
efficiency of the combustion process. The PTP Cast Inlet manifold with increased
plenum volume capacity is also used for optimum performance.
NOTE: Price does not include ECU and 5 AS unit
Key Features
PTP/Janspeed
modified cylinder head.
Cast
Inlet manifold with increased plenum capacity.
Standard
camshafts and valve gear maintained.
Standard
Rover MEMS ECU maintained.
All
service and diagnostic functionality maintained.
140
ps performance based upon the 1.8i engine.
Day-to-Day
driveability maintained.
SVA
emission compliant when used with the standard or PTP sports catalyst.
12
months manufacturing defect warranty.
(Data copied from the ptp-site, www.ptp-ltd.co.uk)
165 Performance
'K' Series Engine Assembly - £4999 (ex VAT)
Power 165ps
at 7000rpm
Torque 140lb/ft at 5000rpm
Power and Torque figures achieved with Janspeed performance exhaust, sports
catalyst and ITG performance induction system. Deviation from these parameters
may result in a different performance level.
The PTP 165 has been designed for upgrade of the K series 1.8i base engine in
either Cylinder head kit form (see Performance Kits) or full engine assembly.
The 165 will achieve UK SVA/MOT legislative requirements when used with the
standard or PTP sports catalyst.
The engine delivers increased top end power and significant improvement in torque
across the whole speed range. The torque curve was generated to give excellent
low speed and mid range throttle response in all gears for optimum vehicle performance
and driveability. The core of the package is a highly tuned cylinder head based
upon that used in the VHPD engine (ie large valve and ports). The head is an
evolution of the 140 again with the modifications focusing not on metal removal
for maximum air flow but port and chamber modifications to bestow optimum efficiency
of the combustion process. The PTP Cast Inlet manifold with increased plenum
volume capacity is also used for optimum performance.
The 165 incorporates new unique camshafts with high efficiency profiles and
lift characteristics, available in both mechanical and hydraulic configuration.
PTP recommend fitment of the mechanical valve gear for Track and race applications
to ensure valve control is maintained at all times. The head is manufactured
for fitment of Manual Timing belt tensioning only and hence the tensioner kit
is supplied as part of the package.
The level of head modifications and the unique camshaft arrangement has necessitated
the need for a complete remap of the engine tune parameters. PTP utilise an
EFI engine management system with unique software and tune parameter elements.
This has resulted in the improvements in performance and an engine operating
range extension to 7300rpm
Key Features
PTP
/ Janspeed modified cylinder head.
Cast
Inlet manifold with increased plenum capacity.
VHPD
based cylinder head (large valves and ports)
New
EFI ECU with the Rev Range extended to 7300rpm.
165ps
performance based upon the 1.8i engine.
Day-to-Day
driveability maintained.
SVA
emission compliant when used with the standard or PTP sports calalyst.
12
months manufacturing defect warranty.
NOTE : ECU and 5AS unit not included in price, £300.00 on cost for mechanical
valve gear option.
(Data copied from the ptp-site, www.ptp-ltd.co.uk)
190 VHPD
'K' Series Engine Assembly - £6750 (ex VAT)
PTP 190 VHPD : (190+bhp)
The 1.8i performance VHPD engine is now very well known. It is used in both
road and race applications in many of today's highly desirable sports cars.
Lotus Exige, 340R, Caterham superlight and the Westfield FW400 to name four.
A very close relationship was used by Rover in their highly successful MGF cup
single make race series.
The engine is available
in fully built form only with an option of either hot test or full run
and rate with performance curve supplied.
This seasons VHPD now incorporates the newly developed PTP multi throttle inlet
manifold and ITG Air Filter lifting the performance over 190bhp when
used in conjunction with optimised intake and exhaust systems. A Rev limit of
7800rpm, Mechanical valve gear, Ultra lightweight flywheel, 8002 Crankshaft,
forged Pistons and con rods, uprated valves and springs are also key elements
of the VHPD. SVA emission compliancy can be achieved but is vehicle application
dependent, please contact us for further details.
NOTE : Price does not include ECU and 5 AS unit
100kg
dry weight
190BHP
K-series
Race engine
Incorporating
unique Racing components
In-line
or transverse installation
Powering
two one-make race series in 1998
Supplied
to three OE Manufacturers
All performance figure's derived on test beds with optimised intake and exhausts,
figures may vary in different applications.
(Data copied from the ptp-site, www.ptp-ltd.co.uk)
Technical information here
220 Evolution
'K' Series Engine Assembly - £9800 (ex VAT)
PTP 220+ bhp Evo Race engine assembly.
The ultimate from
the PTP stable. All aspects of the 140,165HTD,and the VHPD engine development
have been evolved to create the ultimate performance from the K series engine
for the race track.
Highly modified chambers and ports, more unique camshafts, mechanical valve
gear and mechanical timing belt tensioning are key features of the EVO cylinder
head. Lighter VHPD pistons, Steel con rods, Ultra Lightweight Flywheel and a
PTP lightweight steel crankshaft combine to optimise the reciprocating components
in both strength and functionality.
The block structure is also modified and with newly designed liners to increase
rigidity and overall product reliability it copes with the speed and performance
delivered.
The induction system utilises a PTP developed multi throttle manifold designed
in which is now powering the new Lotus 340R and Exige engines.
The Evolution engine is delivered to the customer fully run in and rated ready
for immediate race use. It comes complete with a rated curve from Janspeed Motorsport
/ Race dynamometer that was also used also for all MGF cup engines
The evolution engine performance is significantly improved over that of the
current VHPD. Key features from the 140 and 165 have enable significant gains
in torque over the whole of the engine speed range to be obtained. The maximum
power is in excess of 220hp and seen at 8200rpm with the rev limit set
to 8500rpm.
SVA emission compliancy can be achieved but is vehicle application dependent,
please contact us (being PTP (Erik)) for further details.
All performance figure's derived on test beds with optimised intake and exhausts,
figure's may vary in different applications.
(Data copied from the ptp-site, www.ptp-ltd.co.uk)
Besides the full engines, they also supply performance kits
PTP
Sport 140 kit
Key features
· New (!!) and fully-assembled cylinder head
· New upper and lower modified, cast alloy inlet manifolds with increased
plenum volume capacity (subject to vehicle application)
· A sensible increase in excess of 20bhp over the standard output
· Comprehensive fitting kit and instructions
· Accurate engine dynometer test data.
· PTP body and engine appliqués.
· All products within the SPORT Performance package are NEW, no exchange
or surcharge needs to be considered.
· 12 months manufacturing defect warranty.
· Enhanced driveability
I received the following
info about this kit:
Known as the 'SPORT' engine development in PTP's unique terminology, careful
fine-tuning of components has enabled the K-Series engine in 1.8-litre form
to produce a sensible increase in excess of 20bhp over the standard output (engine
dynometer testing excluded the fitment of our 4-2-1 manifold & flexible
link pipe which may see further gains in power). According to professional,
independent testers (Autocar Magazine; EVO Magazine et al), although the power
has been clearly increased, there are also tangible improvements in mid-range
potency and top-end torque.
Much improved driveability results, with benefits felt in immediacy of throttle
response and a better aural response. The SPORT upgrade relies on the standard
engine management system and other control functions to ensure that maintenance
and diagnostic functions are uncompromised.
The principal component of the performance package is a new, fully built and
highly tuned cylinder head. All products within the SPORT Performance cylinder
head kit are NEW, no exchange or surcharge needs to be considered. The SPORT
is devised as an upgrade for the EU2 and EU3 118bhp K series 1.8i (base) engine
and will achieve UK SVA / MOT legislative requirements when used with the standard
or PTP Sports Catalyst.
The cylinder head and accompanying fitting kit is designed to be easily installed
by any professional garage. All Original Equipment parts and fitting instructions
are included.
To maximise the overall performance of the SPORT cylinder head, PTP recommends
that the ITG air box induction system and Janspeed Supersport rear silencer
are also installed.
PTP
RT-Sport 165 kit
Key features:
· A fully built brand new cylinder head assembly with large valve and
ports.
· New upper and lower modified, cast alloy inlet manifolds with increased
plenum volume capacity.
· New EFI ECU and connector lead.
· Manual camshaft belt and tensioner assembly.
· Original equipment gaskets, studs, nuts and all fittings required for
installation
· Up-rated Spark plugs.
· Cylinder head is supplied in its own purpose built box
· Accurate engine dynometer test data.
· Comprehensive fitting instructions.
· PTP body and engine appliqués.
· All products within the RT-SPORT Performance package are NEW, no exchange
or surcharge needs to be considered.
· 12 months manufacturing defect warranty.
· Day-to-day driveability maintained.
I received the following
info about this kit:
The RT-SPORT delivers outstanding power and torque improvements across the
whole engine speed range, with a potential max power output of 170ps @ 7,300rpm
(Standard 118ps) and 135lb ft of torque across a wide rev-range of 4,750-6,250rpm.
The torque curve was formulated to provide excellent low speed and mid-range
throttle response in all gears to maximise performance whilst retaining the
day-to-day driveability.
Professional testers from several publications have stated that the enhanced
driveability and greater mid-range punch have lifted the engine onto another
plane. While the RT-SPORT emits a purposeful growl during acceleration and at
high engine speeds, around town it remains highly tractable, surprisingly refined
and a genuine wolf in sheep's clothing.
The principal component of the performance package is a new, fully built and
highly tuned cylinder head (i.e. large valve and ports, 165 & 170ps power
derivatives available). Utilising PTP designed camshafts with high efficiency
profile and lift characteristics resulted in the need for a complete re-map
of the engine management system. Using an EFI control unit, with PTP developed
parameters and an increased rev-range from the standard 6,500rpm to 7,300rpm
the package delivers strong improvements.
Included with the cylinder head assembly is a modified cast alloy inlet manifold.
O.E. gaskets, studs, nuts and all fittings needed for installation to the vehicle
are supplied. The head is designed for a manual camshaft belt tensioner system
only, this allows less "whipping" of the camshaft belt at high engine
speeds (a manual tensioner and fittings are included with the RT-SPORT package).
The kit is supplied in its own purpose built box, which can be used to store
the original parts removed from the vehicle.
All products within the RT-SPORT Performance cylinder head kit are NEW, no exchange
or surcharge needs to be considered. The RT SPORT is devised as an upgrade for
the EU2 and EU3 118bhp K series 1.8i (base) engine and will achieve UK SVA /
MOT legislative requirements when used with the standard or PTP Sports Catalyst.
To maximise the overall performance of the RT-SPORT cylinder head, PTP recommends
that the ITG air box induction system, Janspeed sports catalyst converter &
Supersport rear silencer are also installed.
The parts of this
kit in more detail
The fitting instructions of this
kit
Some performance parts
Con rod
set (Steel) - £1000 (ex VAT)
For use in with most arduous Motorsport cycles for the 1.8 K-series engine.
Recommended for power outputs in excess of 200bhp
Con rod set (Forged)
- £406.84 (ex VAT)
Forged con rods
from Rover forging. Machined to PTP requirements for use with the K series engines
over 160bhp and for speeds in excess of 7300 rpm.
The Performance Con rods are shown here with the matching forged Pistons.
Crankshaft (steel Billet) - £1899 (ex VAT)
PTP designed and developed for the Evolution engine to withstand the most extreme
duty cycles. Lightweight and fully balanced, it is recommended for use with
the PTP reciprocating components.
For use with high powered high revving K Series engines (in excess of 200bhp
and over 8000rpm)
Crankshaft 8002 - £433.62 (ex VAT)
Based upon the standard 'K' Series Crankshaft but with a new casting material
specified by PTP to give 17% more strength and is machined to a new specification
defined by PTP.
fig. Crankshaft from PTP Ltd.
This crankshaft
is most commonly used on the VHPD engine with recommendation being used on engines
producing up to 200bhp
Direct to head Multi throttle inlet manifold - £650 (ex VAT)
PTP 99MY Multi Throttle Inlet Manifold
Designed and developed for the Evolution engine, however compliments the VHPD
derivative and increases engine performance over 190bhp without the need for
tune parameter adjustments.
fig. Inlet manifold for multiple throttle bodies
Shown here
as a complete manifold, the Injectors, Fuel rail, Injector harness, Potentiometer,
Stepper Motor are all carried over from original plastic inlet Manifold.
Integral throttle butterflies, reduced weight and an improved air by-pass system
combine with an ITG JC 40/75 Air Filter to give the optimum performance and
stunning looks.
Flywheel (Ultra lightweight) - £159 (ex VAT)
Designed to increase engine responsiveness and to assist in overall balance
and smoothness of the engine. The 30% lighter than standard ultra lightweight
flywheel is fitted on the Motorsport 190 VHPD and Evolution engine. This simple
but effective component can be used with a standard or heavy duty clutch and
comes complete with ring gear and balanced ready for installation.
fig. Lightweight flywheel
Linished
Camshaft Cover - £49.99 (ex VAT)
Linished Camshaft Cover When used in conjunction with the Motorsport 190 Spark
plug insert looks stunning and applies to 1.4, 1.6 and 1.8 versions of the K
Series engine
fig. Camshaft cover
Mechanical
Tappet set - £288 (ex VAT)
Manufactured to PTP specification for mechanical valve gear option and used
in the VHPD engine as standard. Improved valve control are the main advantages
of Mechanical tappet over the standard Hydraulic tappet. This type of tappet
is recommended to support extensive track use without loosing performance.
fig. Tappet set from PTP Ltd.
The
tappets are shown here with the uprated valves and springs also used on mechanical
valve gear option.
Mechanical Tappet
shim set
For use with the 1.8 K Series Mechanical valve gear
To no ones surprise they are responsible for turbo's and superchargers. They also do a kit for the MGF, that's why they got listed on this page..
fig. Turbo-Technics Supercharger
As stated on their site:
"Everyone involved in the engine industry today must be completely familiar
with the advantages of turbocharging. The simple turbocharging concept has served
us well for two decades, the advantages are far from overwhelming, and it is
by no means clear that turbocharging will be the favoured method of increasing
aspiration density in the future. The principal advantages of supercharging
compared to turbocharging include:
- More direct linkage between engine output and operator demand.
- Minimum exhaust-side thermal inertia.
- Minimum under-bonnet heat.
- Smaller size and easier packaging in many applications.
- Potentially lower cost through the avoidance of special materials.
At Turbo Technics, we took the view that package size, weight, and fuel economy
are of paramount importance in our market, and for these reasons we chose to
develop the centrifugal supercharger. The key to this design is a planetary
traction drive relying on friction between rolling elements to provide the drive
force.This approach offers the benefits of:
- Very compact packaging, with minimum length and profile.
- Low weight.
- Low noise.
- High efficiency, particularly at cruise conditions. " (as
found on www.turbotechnics.com)
The Result of their development on a Rover 1.8i K-engine, is an increase in power from 118bhp to 191bhp with a considerable broadening of the usable power band and an increase in torque of 33% at 4,000 revs/min.
The compression ratio will be reduced by fitting new strengthened lightweight pistons and shortened forged connecting rods. These items were designed by theirself. The supercharger will run up to 110.000rpm and is driven by a poly-V belt from the crankshaft. The weight of the charger is minimized to 4.8kgs. The complete exhaust system can be remained, but an upgarde to a performance system can be done for an additional cost. At the side of the intake, a new aluminium inlet manifold wil be fitted. The injection system is kept as standard except two extra injectors. Off course the system needs a new ECU. No other changes are needed.
fig. Cast Aluminium inlet
manifold
Figures
standard
1.8i
|
supercharged
MPi
|
supercharged
VVC
|
|
Maximum power |
118bhp
@ 5500rpm
|
190bhp
@ 6500rpm
|
215bhp
@ 6500rpm
|
Maximum torque |
121lb/ft
@ 4500rpm
|
170lb/ft
@ 5000rpm
|
185lb/ft
@ 6000rpm
|
0-60mph |
8.5s
|
6.3s
|
5.5s
|
30-50mph (4th gear) |
6.6s
|
4.9s
|
1.6s
|
50-70mph (4th gear) |
7.0s
|
5.2s
|
4.8s
|
In the table above, the power value achieved for the VVC was when a sportexhaust system was fitted.
fig. power output graph
for the MPi (left) and the VVC (right) standard (Blue) and Supercharged (Red)
(source: Turbo-Technics)
fiq. torque graph for
the MPi (left) and VVC (right) standard (Blue) and Supercharged (Red)
(source: Turbo-Technics)
The upgrade will ask you £4950.00 + VAT which includes fitting and a 12 month mechanical warranty. If you're opting for the additional exhaust, you can add another £230.00 + VAT to the bill.
For those intested they even do supercharging a Lotus Exige or 340R up to 260bhp....
Well known, especially in the Vauxhall/Opel scenes, QED Motor Sport can offer a wide scale of serious tuning options. It looks like customisation is one of their keywords. Following text is found at their website.
Workshop
Services
Standard Head
Rebuilds
There are three options commonly requested for the standard cylinder head with
applications ranging from fast road to club level competition.
- Fast Road Head Rebuild: The head is stripped,
chemically cleaned and inspected. Valve guides are replaced with our Colsibro
bronze version and stage one cams are fitted.
- Trackday Head Rebuild Package: The head is stripped
cleaned and inspected, with Colsibro bronze guides and stage one cams fitted
as above. In addition the inlet and exhaust ports are lightly worked to improve
gas flow and matched to direct to head throttle bodies, which are supplied and
fitted.
- Clubman Head Rebuild Package: This is about as
far as a standard head can sensibly be developed. Strip, clean, inspection and
fitting Colsibro guides is as above but our stage four cams are fitted (Q425MK
inlet and Q395MK exhaust). Inserts are fitted to convert the standard cam followers
into solid followers, and uprated springs are also included. Oversized inlet
and exhaust seats are fitted and formed to accommodate our oversized valves.
Porting work is more extensive, and as above direct to head throttle bodies
are fitted with ports being matched. Because the cams fitted give higher lift
than standard this head cannot be safely assembled to a standard bottom end.
VHPD/VVC Head Rebuilds
Both of these heads already have larger valves and ports but for motorsport
applications we also offer two further service levels.
- Clubman Head Rebuild Package: The head is stripped
cleaned and inspected with Colsibro bronze guides fitted and our Q425MK/Q395MK
cams. Inserts are fitted to convert the standard cam followers into solid followers,
and uprated springs are also included. The standard valves are reused. Porting
work improves gas flow and matches to direct to head throttle bodies. Because
the cams fitted give higher lift than standard this head cannot be safely assembled
to a standard bottom end.
- Full Race Head Rebuild Package: Our ultimate
race head. The head is stripped, cleaned and inspected before Colsibro guides
are fitted. Our most aggressive cams are fitted, along with solid lifter inserts,
and race springs, platforms, and retainers. Our own VVC/VHPD sized valves are
also fitted. Ports are carefully worked to the highest level and matched to
a set of direct to head throttle bodies. Because the cams fitted give higher
lift than standard this head cannot be safely assembled to a standard bottom
end.
Short Engine Rebuilds
As well as head modifications we can also supply, for the more developed engine,
rebuild services for the bottom end of the engine.
- Basic Bottom End Rebuild: The block is stripped,
checked, and chemically cleaned. Reassembly includes fitting new heavy-duty
end bearings and our banded cylinder liners to improve bottom end strength.
Also included is a full balance.
- Performance Bottom End: The block is stripped,
checked, and chemically cleaned. As with the basic rebuild, heavy-duty end bearings
are fitted as well as our banded cylinder liners. The standard rods are re-used
but honed for standard sized, forged pistons. Although the rods are re-used,
the rod bolts are replaced. Also included is a full balance.These pistons accommodate
higher lift cams and so this is the basic level of short engine rebuild required
for the Clubman head or above.
- All Steel Bottom End: The block is stripped,
checked and cleaned, and then rebuilt with all steel internals. Heavy-duty end
bearing and banded cylinder liners are fitted as above but to further strengthen
the bottom end Carillo type steel con rods are fitted, and a steel crank. Forged
pistons are fitted allowing the use of high lift cams. A lightweight steel flywheel
is fitted using heavy-duty flywheel bolts, and the engine is fully balanced.
Complete Engines
Of course with combinations of the options available above we also offer complete
engines, sold on an outright basis .
- Trackday Engine: A base unit from our stock is
stripped and rebuilt to include modifications suitable for fast road/light motorsport
applications. The block is stripped and rebuilt with heavy-duty end bearings
fitted and the complete assembly is balanced to further improve bottom end durability.
A standard cylinder head is rebuilt to include our Q375HK cams and although
standard sized valves are reused they run in Colsibro bronze guides. For induction
the head is assembled with direct to head throttle bodies. Ignition is with
the standard coil but managed by a programmable ECU which is supplied with it's
own engine bay wiring loom.The completed engine is then run in, mapped and power
tested on our dyno. An even more durable variation of this engine can be supplied
for more aggressive track use including banded liners for extra bottom end strength
and optionally a dry sump and/or race clutch and flywheel.
- Basic Club MotorSport Engine: A base unit is rebuilt to include modifications that make it more suited for club level motorsport applications. The block is stripped and our banded liners are fitted along with forged pistons, and heavy-duty end bearings for extra strength. Although standard rods are reused the con rod bolts are replaced for greater strength, allowing safe use of a higher rev limit. A standard cylinder head is rebuilt to include our Q425MK and Q395MK profile cams, which includes fitting uprated valve springs and converting to solid cam followers. The head is also fitted with oversized valves, running in Colsibro bronze guides, and considerable porting work is carried out to improve gas flow. Direct to head throttle bodies are used for induction and porting work includes matching the head and bodies. The throttle bodies are fitted in our most compact arrangement using pico injectors and carbon fibre trumpets. Ignition is distributorless with a coil, ECU, and wiring loom included.The completed engine is then run in, mapped and power tested on our dyno. Variations of this engine are also supplied with a dry sump and/or race clutch and lightened flywheel for more dedicated track use.
Some
Performance Parts
Camshafts
Stage one (hydraulic): Using a Q375HK inlet cam
with a matching exhaust cam this first stage cam combination is ideal for fast
road or occasional track use. These cams are easily fitted without extensive
engine modifications. When fitted to an engine with throttle body induction
system these cams give approx. 150bhp before 7000 rpm. In a fully race prepared
engine this cam can achieve its full potential, delivering over 175bhp.
Stage two (hydraulic): Using a Q425HK inlet cam
with a matching exhaust cam this second stage cam combination is for more dedicated
motorsport use. Although this is a hydraulic profile the 0.425 lift requires
the uprated VHPD type valve springs. To fit at optimum timing these cams also
require pistons with deeper valve pockets. Using a standard cylinder head, 160bhp
is achieved and in a fully race prepared engine peak power should be approximately
170-180bhp.
Stage three (mechanical): Using a Q395MK inlet
cam with a matching exhaust cam this is the first of our mechanical combinations
and is about as far as aggressive a profile as can be fitted for road use. These
are a mechanical profile and require solid cam followers as well as pistons
with deeper valve pockets and uprated valve springs. With some porting work
to the cylinder head, and a throttle body induction system these cams give a
road useable 170bhp and in a fully race prepared engine can deliver up to 190bhp.
Stage four (mechanical): Using a Q425MK inlet cam
with a Q395MK exhaust cam this mechanical cam combination sees considerable
torque gains at mid range rpm making this cam combination very useful for rally
style applications. As a mechanical profile these cams again need solid cam
followers, pistons with deeper valve pockets and uprated valve springs. With
a suitable cylinder head, throttle bodies, and an appropriate exhaust system
these cams give over 200bhp.
Stage five (mechanical): Using a Q455MK inlet cam
with a Q425MK exhaust cam this combination is our current racing specification.
Suitable for use only in fully race prepared engines where this cam easily achieves
210bhp and in excess of 160 ftlb of peak torque. Our development engine when
fitted with these cams has produced 227bhp.
VVC conversion cams: The VVC in its standard form
has three cams, with the two inlet cams geared together. Competition profiles
for this unusual arrangement are not yet available. Instead we offer a traditional
one-piece cam as a direct replacement. Our VVC replacement cams are available
as any of the motorsport profiles mentioned above. In this way the VVC head
is no longer using variable valve control and customers are free to exploit
the larger valve and port sizes of the VVC head casting.
Valves
The
standard K series cylinder head:
The K series engine was first developed with a 1400cc capacity and very few
changes have been made to the cylinder head since then. Since the 1400cc engine
has 27.7 and 24.0mm valves maths suggests that an 1800cc engine should have
31.4 and 27.2mm valves. Unfortunately as standard there isnt enough room.
Our larger than standard (29mm inlet, 26.4mm exhaust) valves are the largest
that can usefully be fitted on standard seats in front of a standard shaped
port. The QED inlet valves also have the further benefit of a wasted stem. This
reduces the diameter of the valve stem where it would normally interfere with
the gas flow and incidentally makes the valve slightly lighter.
The VVC/VHPD K series cylinder head: There are
obviously differences between these two cylinder heads but for the purposes
of discussing valve sizes they are the same. In both cases Rover presumably
realised that for a high performance engine they would need a different head
casting and so the heads for these engines have larger port sizes and come with
larger valves as standard. Since the standard VVC sized valve is already big
enough* our valves are no bigger, just a different design. As with our 29mm
valves the last portion of the inlet valve stem has a reduced diameter to improve
gas flow, but since these valves are larger, and with consideration of the stresses
on the valve train at high rpm, we have also worked to reduce the valve weight.
In the case of the inlet valves, for example, the QED valve is almost 10% lighter
than the OE item.
Pistons
Forged Forged Pistons: Our forged pistons are available
for 80mm bore size (standard 1600/1800cc bore size) and all give deeper valve
pockets than standard pistons, allowing the safe use of cams with higher lift.For
use in more developed engines we can also supply forged pistons which will typically
raise the compression ratio to 12:01. We can also supply low compression pistons
suitable for turbo/supercharged applications.
Liners
Banded Liners: In racing applications where the
engine is under more extreme stresses both in terms of load and temperature
the standard cylinder liners have been observed to fail. To strengthen the liners
and overcome this limitation we have developed our reinforced, or banded, liners.
Throttle Bodies
Tapered single bodies: The original option for
the K-series was a group of four single 45mm bodies that fit to a tapered inlet
manifold. These offer unrestricted high rpm breathing as well as maximising
mid range torque. The kit includes four bodies, inlet manifold, fuel rail and
fitments.
Direct to head bodies: The ultimate in throttle
body evolution, these bodies, as their name suggests, are designed to fit directly
to the cylinder head, disposing of the need for an inlet manifold. Dyno development
shows 42mm parallel bodies offer equivalent performance to the tapered type
bodies. However fitment is simpler, and overall weight, as well as required
space is reduced. In the least space consuming arrangement, with more compact
injectors, overall length from cylinder head face to the ends of the trumpets
is less than 7 inches.
>> More info on the page about Throttle
Bodies. <<
Engine Management System
DTA Competition engine management systems: Our
involvement with DTA management systems goes back many years and when building
a motorsport engine we wouldn’t think of using any other system. The DTA ECU
represents the state of the art in engine management systems. Full 3d mapping
of both fuel and ignition, two stage rev limiter, shift light output, fuel pump
control, transient fuel compensation (acceleration boost), closed loop fuel
mapping, and a three minute data log are amongst (but not all of) the features
available.Despite the wide capabilities of the DTA ECU the control software
is straightforward and simple to use. All of the settings are explained in the
comprehensive manual supplied with the software. For motorsport engines (and
especially for engines that will develop with each racing season as part of
an ongoing project) the DTA system is without doubt the management system of
choice. The DTA systems are capable of using a wide range of sensors including
the majority of those fitted to the K series engines as standard and these systems
are provided with an engine bay wiring loom.
>> More info on the page about chips and
management systems. <<
Lubrication
Steel oil pump inner gear: The standard gears,
which are mass-produced in a sintered material, have been seen to fatigue and
eventually break up when subjected to the greater speed and vibration encountered
in a race engine. Our gears, which are formed by spark erosion from heat-treated
carbon steel, are a sensible precaution even for a lightly modified K series
engine if it will be used aggressively. For a race engine they are an essential.
Dry Sump System: The K series engine is found in
a wide range of vehicles and so our dry sump system has been developed to be
adaptable for almost any installation. We supply the system as a kit, including
our . . .
. . . three stage pump:
- Compact design fits close to the
engine.
- Twin scavenge stages - creates sump
vacuum very effectively
- Single pressure stage - a race worthy
replacement for the standard pump
- Multiple choice of port position
- enabling use in a wide range of installations
- Adjustable pressure relief valve
- for different levels of engine tune and application
- Sump pan and baffle - our cast dry
sump pan, fitted with an efficient windage plate, can be adapted for any application.
... and of course, hoses, mounting brackets, etc
B r o d i e B r i t t a i n R a c i n g ( B B R - G T i )
(all taken from the BBR website)
Phase
One "Super 140"
(£995 ex. VAT and sold as a kit, £1,295 ex. VAT, fitting included)
BBR developed the Phase One in conjunction with Bell & Colvill, one of the country’s
leading Lotus dealers, for use on the Elise. After supplying these exclusively
to B&C, we are delighted to now offer them for all K-Series applications. The
conversion comprises a specially designed stainless steel exhaust system (all
emission controls remain intact), coupled with a dynamometer-programmed version
of BBR’s unique Interceptor 2000 to handle the revised fuel and ignition requirements
of the engine. Performance is usefully improved throughout the entire range,
making what is already an exciting sports car even more punchy!
Comprising the following
BBR special components:
1. Free-flow stainless steel exhaust system with polished, rolled edge tailpipe/s,
fitted on to the original cat’.
2. Interceptor 2000 fitted to the manufacturers ECU. This device enables the
engine’s running software to be modified, taking advantage of the low back-pressure
exhaust system.
3. High flow air filter.
Power is raised from a lowly 118bhp to approximately 140bhp (+/- 5%) @ 6.800rpm
with a very useful 14lbsft increase of torque. This is by far the best value
and most popular conversion, more than 160 having already been sold world-wide
with over 100 in the UK. The interceptor is the catalyst for Phase One and Two
normally aspirated conversions to the "K" series engines and once fitted, only
software updates are required to suit the more radical modifications. For upgrading
from Phase One to Two, therefore, a substantial discount is available since
Interceptor 2000 is already fitted.
Phase
Two "Super 160"
(£1,800 ex. VAT and sold as a kit, £2,395 ex. VAT, fitting included)
The BBR Phase Two is for those drivers who want more out of their MGF than a
Phase One can offer but who don't (yet!) want the raw power of a Turbocharger.
The Phase Two comprises all that in the Phase One and also a pair of specially
designed camshafts, timed in such a way as to maintain a smooth idle and the
vehicle's low emission output. One distinct advantage of this conversion is
that the upgrade from Phase One to Super Phase One can be carried out at very
little expense and on a while-you-wait basis.
Comprising the following
BBR special components:
1. Free-flow stainless steel exhaust system with polished, twin rolled edge
tailpipes, fitted on to the original cat’.
2. Low-overlap, fast road camshafts.
3. Vernier timing
wheels for optimum timing and performance.
4. Interceptor 2000 fitted to the manufacturers ECU. This device enables the
engine’s running software to be modified, taking advantage of the low back-pressure
exhaust system and revised valve timing.
5. High-flow air filter.
The characteristics of the cam profiles, together with the revised ECU software,
enable vehicles to comply with the latest emission regulations for petrol vehicles
– the vehicle remains "MOT friendly" and idle is unaffected. Power is raised
from a lowly 118bhp to approximately 158bhp (+/- 5%) @ 6.800rpm with
a very useful additional extra 20lbsft of torque.
Phase
Three "Super 185"
(£9,000 ex. VAT, fitting included)
The BBR Phase Three is as far as you would sensibly want to go with a normally
aspirated engine. Anything beyond this would be quite unpleasant for road use.
This conversion is fitted with a gas-flowed, big valve cylinder head, special
fast road/rally camshafts, free-flow stainless steel exhaust system, free-flow
air filter element and the Interceptor 2000. It is very definitely not while-you-wait.
Comprising the following
BBR special components:
1. Forged steel crankshaft.
2. Forged steel connecting rods.
3. Forged aluminium alloy pistons.
4. Free-flow stainless steel exhaust system with polished, twin rolled edge
tailpipes, equipped with a sports cat’ specially developed by Johnson Matthey
for BBR Ltd.
5. Low-overlap, fast road camshafts.
6. Vernier timing wheels for optimum timing and performance.
7. Higher rate valve springs.
8. Gas-flowed cylinder head with oversize valve seats, inlet and exhaust valves.
9. Cast alloy inlet manifold, plenum chamber and throttle elbow.
10. Larger throttle butterfly assembly.
11. Induction/filter system.
12. New fully mapped engine management system.
The new management system incorporates closed loop Lambda operation, the only
way to maintain compliance with EC emission regulations for gasoline powered
passenger vehicles Oct.1st ’97. The software has been carefully mapped on our
Superflow 7100 dynamometer for optimum performance whilst maintaining excellent
fuel consumption characteristics. Power is raised by this conversion from a
lowly 118bhp to approximately 185bhp (+/- 5%) @ 7,500rpm with a useful
increase in torque.
Low Pressure
Turbo "LPT160"
(£4,000 ex. VAT and sold as a kit, £5,000 ex. VAT, fitting included)"
As would be expected from our repuation, we are finalising a range of turbocharged
variations for the MGF. The BBR LPT160 conversion is the first stage, requiring
the minimum amount of internal engine work. This conversion greatly enhances
acceleration due to the significant increase in torque that is not generally
achievable with normally aspirated conversions. The LPT160 is an introduction
to the exciting world of turbocharging.
Comprising the following
BBR special components:
1. High temperature cast iron-alloy exhaust manifold.
2. Hybrid Garrett
T25 turbocharger
3. Revised inlet air box/filter system
4. Free-flow stainless steel exhaust system with polished, twin rolled edge
tailpipes, fitted on to the original cat’.
5. New electronic engine management system.
Power is raised from a lowly 118bhp to approximately 168bhp (+/- 5%) @ 5,000rpm
and torque has been raised from 122lbs ft @ 3,000rpm to 175lbs ft @ 3,250rpm.
Medium
Pressure Turbo "MPT220"
(£10.000 ex. VAT, fitting included)
The next stage up the ladder for turbo enthusiasts is theBBR MPT220. Requiring
a fair amount of internal engine work, very respectable power is achieved -
enough to blow off all but the very pricey Super Cars.
Comprising the following
BBR special components:
1. High temperature cast iron-alloy exhaust manifold.
2. Garrett T25 turbocharger
3. Forged aluminium alloy pistons.
4. Forged steel high performance connecting rods (changed pin centres)
5. Cylinder liner kit.
6. Cast inlet manifold and plenum chamber system.
7. Intercooler system.
8. Revised inlet air box/filter system
9. Gas-flowed cylinder head.
10. Special cylinder head gasket.
11. Free-flow stainless steel exhaust system with polished, twin rolled edge
tailpipes, fitted on to a metallic substrate sports cat’.
12. New electronic engine management system.
Power is raised from a lowly 118bhp to approximately 220bhp (+/- 5%) @ 5,500rpm
and torque has been raised from 122lbs ft @ 3,000rpm to 190lbs ft @ 3,250rpm.
MGF 300
Turbo
The BBR MGF 300 Turbo conversion is aimed at the driver who wants the ultimate
performance from this great little car. The 300bhp engine at the heart of this
conversion was developed and built originally for the Maclaren chief designer,
Adrian Newey. This astonishing power output from the K-Series engine gave his
Lotus Elise performance comparable to the world's fastest super cars and the
same power to weight ratio as the Maclaren F1 road car! The project took 14
months to complete and will shortly be undergoing it's first magazine tests.
Component parts are now available and all of these are either designed in-house
by our own engineers or produced to our specification. Just imagine it, instead
of an F40 Ferrari you can purchase a BBR modified MGF with similar performance
and still have enough loose change left to buy a substantial house and garage
to keep it in!
Engine statistics in
a nutshell
BBR.-GTi modified "K" Series Rover 1800cc 4 cylinder 16 valve
- Bore = 78 mm
- Stroke = 89 mm
- SV/cyl = 425.27 cc
- Total SV = 1,701.09 cc
- CR = 8.5:1
Turbocharged
Max power output = 305 bhp at 6,800 rpm
Max torque = 285 lbs ft at 4,250 rpm
Torque spread min 235lbs ft at 3,500rpm to 6,800rpm
Max engine speed = 7,200rpm
Max boost = 1.3 bar (2.3 bar abs.)
Schedule of engine improvements
and chassis installation modifications
*
Part One, BBR new engine parts and alterations
- Forged, nitrided
steel counterbalanced crankshaft.
- Stronger, heavy-duty cylinder liners.
- Forged aluminium alloy pistons with changed compression height, larger diameter
gudgeon pins and lightweight rings.
- Cylinder block machined for new liners.
- Ladder frame doweled to cylinder block at all main bearing shuts.
- New forged HT steel connecting rods - larger gudgeon pin diameter, new length
to suit pistons.
- Steel crankcase strengthening base-plate machined to accommodate bigger diameter
crankcase studs and drilled with special oil galleries to attach piston oil
spray plumbing.
- Specially manufactured larger crankcase-to-cylinder head HT steel studs.
- Specially manufactured HT steel cylinder head and crankcase nuts.
- Oil spray piston cooling system plumbed to steel base plate and attached to
the cylinder block.
- Cylinder head machined and fitted with larger inlet and exhaust seats.
- Larger tuftrided nickel-steel inlet and exhaust valves.
- Cylinder head gas-flowed.
- Cylinder head machined for stronger gasket arrangement and to fit new exhaust
manifold.
- Stronger cylinder head gasket.
- New inlet manifold, plenum chamber and throttle elbow - designed to maximise
mass airflow with pulse tuned induction length and calculated optimum plenum-chamber
volume. Design uses a larger butterfly assembly with attached throttle angle
sensor. Castings are black anodized aluminium alloy but magnesium castings are
available at extra cost.
- Larger fuel injectors.
- Fuel rail assembly fitted with manifold pressure adjustable fuel pressure
relief valve.
- Fabricated stainless steel exhaust manifold plumbed underneath the engine
to attach to turbocharger on inlet side.
- BBR built and balanced hybrid Garrett T3 turbocharger fitted with BBR 360¡
heavy duty thrust bearing.
- Specially manufactured heavy-duty single plate clutch, organic linings. (no
space in bell housing for twin plates)
- Dyno tested engine. Software written for both fuel and ignition to suit all
situations; e.g.
Warm-up cycle -
warm-up maps
Slow running - slow
running maps
All other throttle
and load positions - main maps
Boost control
Closed Lambda loop
Taking into consideration:
Intake air temperature
Coolant temperature
Intake air (manifold
absolute) pressure
Throttle angle
Limit parameters
*
Part two, in chassis
- Strengthened gearbox
- new closer ratio gears; long first gear (70mph; 112kph)
- BBR LSD new limited slip differential.
- BBR /Johnson Matthey metallic substrate sports cat.
- Stainless steel exhaust system, straight through silencer.
- Water to air charge cooler to control induction temperatures. Accommodated
to the rear of the car but plumbed to a water radiator mounted in front of the
main coolant radiator, coolant being circulated by an electric pump, activated
by inlet air temperature/boost level.
- Special in-car plumbing for turbo pipework (including oil feed and drain).
- New engine management control computer and loom, connected to original sensors,
except throttle angle sensor, attached to the new throttle body.
- Fuel system incorporates new pumps, swirl pot and plumbing.
- Engine breather system.
- Modified engine-cooling system incorporating swirl pot and expansion tank.
- Remote oil cooler and oil filter unit
NB: Dry sump kit, optional see below.
K300T Parts List at a
glance
1 off Forged billet
steel crankshaft
4 off Forged steel connecting rods
4 off Heavy duty cylinder liner
4 off Forged lightweight aluminium alloy heavy-duty performance pistons
4 off Lightweight, high performance, piston ring pack
8 off Oversize inlet valves
8 off Oversize exhaust valves
16 off Oversize valve seats
1 off Cast BBR high performance turbo inlet camshaft
1 off Ditto exhaust camshaft
16 off High performance valve springs
1 off Steel cylinder block strengthening base plate
10 off Crankcase/cylinder head fixing studs
10 off Cylinder head nuts
1 off Heavy duty clutch assembly, organic plate
1 off Cast aluminium alloy inlet manifold
1 off Cast aluminium alloy plenum chamber
1 off Cast aluminium alloy throttle elbow
1 off Throttle assembly
4 off Solenoid higher flow fuel injectors
1 off Fuel rail
1 off Fuel pressure relief valve
1 off Stainless steel exhaust manifold
1 off Stainless steel downpipe (to turbo)
1 off Turbocharger Garrett/BBR T3 hybrid
1 off Stainless steel exhaust pipe, turbo to catalyst
1 off High performance catalyst
1 off Catalyst to silencer link pipe (s.st)
1 off Stainless steel silencer
1 off Polished stainless steel tailpipe assembly
1 off Turbocharger compressor to intercooler pipework
1 off Intercooler water to air type
1 off Intercooler water cooling radiator
1 off Small bore water pump intercooler circulation
1 off Intercooler to throttle assembly pipework and intercooler water-cooling
plumbing
1 off Airbox
1 off Highflow air filter
1 off Airbox to turbocharger inlet pipework
1 off Engine management computer
1 off Engine management wiring loom and connector
1 off MAP manifold sensor
1 off Water temperature sensor
1 off Lambda sensor
1 off Throttle angle sensor
1 off Air temperature sensor
1 off Engine speed sensor
1 off Camshaft/engine position sensor
1 off Catalytic converter stainless steel substrate, heavy loaded Platinum/Rhodium
coating
Optional recommended
for track use
BBR.-GTi dry sump
kit, comprising:
- Dry sump (modified
from original and including twin scavenge pick-ups and strainers)
- Dry sump pump twin scavenge
- Dry sump pulleys, brackets and belt
- Dry sump oil tank
- Dry sump pipework
M G X - P o w e r : K 2 0 0 0 E n g i n e
More info on the following page.
2.5 KV6
engine swap
The story starts when Chris Flanagan could manage to put his hands on a brand
new 2.5 liter KV6 engine. At that time, he is still active as an MG Rover technician.
Off course this engine swap isn't as easy as adding one to one. Chris started
with the removal of the K4, installed the V6 on the subframe (the sump needs
some modifications) and changed the engine mounts. After that he continued by
dropping the body and cutting away lumps where the body touched or fouled the
engine. No need to say that creating new panels, welding and some reinforcing
was required. Even the fuel tank needed to be modified. The new tank has a third
less of capacity. Very remarkable is that the precious bootspace hasn't been
touched at all. Instead he has chosen to cut away the front engine bay bulkhead
to clear the front bank of cylinders. To access the spark plugs of the rear
bank of cylinders, he has cut an access panel in the rear bulkhead. To improve
cooling an new radiator and remote oil cooler got installed. Besides an upradted
suspension and braking, modifications to the exhaust were made. He even managed
to install the ZT engine management electronics instead of the ZS box. This
results in a claimed 190bhp instead of the ZS' 180.
Allthough it allready looks very impressive, it is still a prototype.
Contact details:
Chris Flanagan
Spen Vale Garage
Cleckheaton
Tel.: 01274 - 872972
Fax.: 07709 - 248220